Feature:
1. Used to replace the entire system for Xiaomi M165PRO scooter, 1:1 for Xiaomi high imitation scooter.
2. It adopts high?performance 32?bit MCU, protection functions for abnormal conditions such as overvoltage, overcurrent, overheating and undervoltage.
3. Cruising control. Braking energy recovery. Adjustable speed limit.
4. Sports and comfort mode switching. Double closedloop system, quiet operation, smooth cut in secondary acceleration.
5. Smooth cutting in, easy to install, long service life, durable.
Specification:
Condition: 100percent brand newItem type: Brushless Motor ControllerMaterial: plasticColor: As picture shownWeight: Approx. 364g Content: Controller + Meter + Throttle + Front Light + Tail Light + Connecting Wire
Power parameters:
Maximum speed: 27KMH
Climbing angle: less than 15 degrees
Maximum torque of driving motor: 35NMx2
Maximum power of drive motor: 350Wx2
Instantaneous maximum power: 700W
Motor control mode: sinusoid vector control, current + speed closeloop control algorithm1. Turn on
Long press to turn on. When the system is turned on, it sounds "Do Re Fa"
2. When long press again, the system shuts down and sounds "Fa Re Do" at the same time
3. Low battery alarm when the battery is below 30V, the bottom light flashes (entering the low battery warning state, accompanied by 6 buzzers, 31V to exit the low battery warning state).
4. Ultra low speed mode
In the lowpower state, the motor enters the ultralowspeed rotation mode and push the throttle to the bottom. At this time, the digital power supply voltage has been increased to enter the normal power state, and the motor should still be in the ultralowspeed rotation mode. The motor can enter the normal driving mode only when the throttle is reset to the initial state
5. Brakes
The brake cable is a red 3P 510053P female shell interface cable. The interface is defined as red (+5V), white (signal pin), black (GND) and supports Hall type and switch type brake levers. (The switch type can be braked by shorting the red and white wires) When braking, the tail light flashes
6. Throttle
The throttle cable is a white 3P 510053P female shell interface cable. The interface is defined as red (+5V), green (signal pin), black (GND)
7. Light control
Short press the button to switch the front headlights and taillights together, accompanied by the "Mi La" sound
;
Press the headlights again and the taillights go out with the "LaM" sound.
8. High and low gear switch
Press the button twice in succession, the high and low gears will switch between the red and green lights, accompanied by the "La" sound. The speed of the motor is different in the two gears. Lowend 15KMh, highend 25KMh
9. Throttle failure alarm
The throttle is not plugged in or it is broken, the buzzer sounds three times with the "La" sound
, then stops, and then three times, a total of three times
10. Motor Hall fault alarm
Check the motor Hall wire. If it is not plugged in or broken, the buzzer will sound four times with the "La" sound
, then stop, and then beep four more times, a total of three times
.
Package List:
1 x Head controller
1 x Motor controller
1 x Communication assembly line
1 x Throttle Assembly
1 x Front light board assembly line
1 x Tail light
1 x Protection cover of head controller
1 x Accessories for protective cover
1 x Protective cover sticker
Note:
Please note that the new type and old type of this product will be sent randomly, and make sure you will not mind before ordering.Used to replace the entire system for Xiaomi M165PRO scooter, 1:1 for Xiaomi high imitation scooter.
It adopts high?performance 32?bit MCU, protection functions for abnormal conditions such as overvoltage, overcurrent, overheating and undervoltage.
Cruising control. Braking energy recovery. Adjustable speed limit.
Sports and comfort mode switching. Double closedloop system, quiet operation, smooth cut in secondary acceleration.
Smooth cutting in, easy to install, long service life, durable.
